How to Waterproof a Basement – A Comprehensive Guide

Many London homes have a basement, as this was popular from the Victorian times right up until the present; land is expensive in our capital city and adding below-ground living space is a very attractive proposition. You can’t build up or sideways, but with planning permission, a basement is an effective way to add living space to a home.
In this short article, we present the most common ways to waterproof cellars and basements.

Basement Tanking in London

As you would expect, basement waterproofing is a busy industry in London; sitting on a bed of clay, there are many wet regions where buildings require basement tanking. When a homeowner books a survey, we carry out a thorough damp inspection throughout the building, with special attention on the basement.

The common method involves removing all plaster from the walls and ceilings, then cleaning the substrate. A thick layer of waterproof render is applied and when this is completely dry, a second layer is applied, which forms a watertight seal; a skim of plaster and the walls are complete. The ceiling would be special water proof membrane with several coats of waterproof plaster and the floor might require channels dug out and a special membrane installed, which should keep the interior dry.

Cavity Drainage System

This is the best solution for a basement in ground with high moisture content; basically, the ceiling, walls and floors are fitted with a special studded membrane to create a cavity, which holds any water and there are grooves in the floor to send water to a sump, where it is pumped to drainage points. This is a major project that might take up to a week to finish; everything would be removed and all debris taken out before the damp-proofing work can start. Once the work has been completed, regular inspections should be done to ensure there are no leaks.

Ventilation

Every basement requires a positive rate of airflow, which can be achieved with extractor fans at both ends of the basement. This is essential in order to keep the air dry and if you install some form of heating, this will help keep moist at bay. A large underground space would require a ducting network for both heating and ventilation and a sump pump might be required.

New Builds

If a basement is under construction, it is much easier to waterproof, as the membrane can be fitted during the building process. If you are still in the planning stage of the build, having the ground surveyed will help you choose the best tanking method and you can liaise with the builder.

Damp-Proofing Contractors in London

While we do not carry out damp-proofing work, we do have a close working relationship with the best damp-proofing contractor in London and they offer a solid 30-year warranty on all of their work. We have been surveying London homes for many years and if you would like an accurate evaluation by a certified professional of your London home, call London Damp Specialists on 020 7205 4886 or complete the online booking form and one of our damp surveyors will arrange to inspect the property.

 

Damp Survey Costs

Transparent pricing with no hidden fees for our independent, unbiased surveys.

Level 1

Level 1

£199 + VAT

What’s included:

  • Inspection of walls
  • Inspection of floors
  • Inspection of ceilings
  • Leak inspection of drains and plumbing
  • Damp information and prevention guide
Level 2

Level 2

£299 + VAT

What’s included:

  • Everything in Level 1
  • Dry rot inspection
  • Wet rot inspection
  • Woodworm inspection
  • Damp information and prevention guide

 Survey Add Ons

Add On 1

£299 + VAT
Lab Analysis Of Plaster

Laboratory analysis Of plaster identifies hygroscopic salts such as chlorides and nitrates. which indicate whether damp is caused by rising groundwater or by plumbing leaks, This testing removes guesswork, allowing the exact source of moisture to be identified so the correct treatment is applied rather than carrying out unnecessary damp-proofing work.

Add to Survey

Add On 2

£299 + VAT
Mould Lab Swab Testing, qPCR on DNA

qPCR DNA mould testing detects microscopic mould spores that are invisible during a normal inspection and van remain hidden behind walls, floors. or inside building rkaterials. It identifies the exact mould species present and the contamination level, allowing hidden mould problems to be confirrned and properly treated before they affect the property or occupants’ health.

Add to Survey

Qualifications: All our surveyors are PCA and CSRT qualified for remedial treatments and also CSSW qualified for structural waterproofing.
Next day report: You will receive the report within 24 hours of the inspection taking place.

These are the tools we use

Damp Meter

Damp Meter

A damp meter is a diagnostic tool used to detect and measure moisture levels within building materials such as plaster, brick, timber, and concrete.

Borescope camera

Borescope camera

borescope camera is a small inspection camera attached to a flexible semi-rigid cable that allows you to see inside areas that are otherwise inaccessible.

Drone Inspection

Drone Inspection

A drone is a remotely operated aerial device equipped with a camera that allows visual inspection from above without the need for scaffolding or ladder.

Air Humidity Sensor

Air Humidity Sensor

Air humidity sensor measures the amount of moisture present in the air, expressed as relative humidity (RH) in percentage. It helps determine whether indoor conditions are contributing to condensation, mould growth, or damp-related issues.

Thermal Imaging Camera

Thermal Imaging Camera

A thermal imaging camera detects temperature differences on surfaces by using infrared technology to produce a heat map image. In damp investigations, it helps identify cold spots, moisture intrusion, insulation defects, thermal bridging and leaks.

Air Flow Ventilation Detector

Air Flow Ventilation Detector

An air flow ventilation detector measures the movement and volume of air passing through vents, extractor fans, and air bricks. It confirms whether ventilation systems are working properly and achieving adequate air changes within a room. Poor airflow leads to trapped moisture, high humidity, condensation on cold surfaces, and ultimately mould growth.

Mould Lab Swab Testing

Mould Lab Swab Testing

A mould swab test is carried out to confirm the presence of hidden mould growth and identify the specific species involved. Surface mould is not always visible, especially behind furniture, inside cavities, or within ventilation systems. Laboratory analysis of a swab sample determines whether active mould spores are present and what type they are, which helps assess potential health risks and decide the correct remediation approach rather than relying on visual assumption alone.

Lab Analysis of Plaster

Lab Analysis of Plaster

Laboratory analysis of plaster is used to identify the type of salts present within the material, typically chlorides and nitrates. The presence and concentration of these salts help determine whether the moisture source is consistent with rising damp, ground contamination, or another forms [sic] of water ingress. such as mains water leak, This removes guesswork and prevents misdiagnosis, ensuring the correct remedial treatment is specified rather than applying unnecessary or ineffective solutions.

 

Contact Us

If you have some questions, please complete this form:

Book and Pay for a survey

If you are ready to book a survey and pay, please complete this form:

Book Survey